Download fulltext HTML
S.V., G., O.M., I., A.G., I., & M.S., K. (2019). Relationship Between the Texture and Young’s modulus over the Section of Cold-rolled Rods of Low-modulus Biocompatible Alloy. KnE Engineering, 4(1), 74–81. https://doi.org/10.18502/keg.v1i1.4393

https://doi.org/10.18502/keg.v1i1.4393

statistics

  • 374 Abstract Views
  • 471 PDF Views
  • 0 HTML Views

authors

  • Grib S.V.
    No author data available.
  • Ivasishin O.M.
    No author data available.
  • Illarionov A.G.
    No author data available.
  • Karabanalov M.S.
    No author data available.

Published Date

  • Apr 15, 2019

Relationship Between the Texture and Young’s modulus over the Section of Cold-rolled Rods of Low-modulus Biocompatible Alloy

KnE Engineering / XIX International scientific-technical conference “The Ural school-seminar of metal scientists-young researchers” / Pages 74–81

Abstract

The influence of the texture type on the Young’s modulus value in the different sections of cold-deformed rods of Zr-31Ti-18Nb alloy (IMP BAZALM) was studied. It was found, an increase in the compression deformation degree from 63 to 84 % of Zr-31Ti-18Nb alloy during cold rolling contributed to the improvement of {001} <110> deformation cube texture. This contributed to the preferential orientation of the directions <001> and <110> parallel to ND and RD (TD) directions, accordingly. The minimum values of the Young’s modulus were typical for areas where low-module <001> orientation prevailed, and the maximum values of the Young’s modulus were characteristic for areas with high-modules <110> orientations. So, in the alloy deformed by 84 %, the lowest values of the Young’s modulus were obtain in the rolling plane up to 53 GPa, and the highest values in plane perpendicular to the rolling direction up to 70 GPa.


 


 


Keywords: Zr-Ti-Nb system, biocompatible alloy, Young’s modulus, texture.

References
[1] I.O. Skyba, O.P. Karasevska, B.M. Mordyuk, P.E. Markovsky, V.M. Shyvanyuk, Effect of strain-induced β→ω transformation on mechanical behaviour of β-titanium and β-zirconium alloys, Metallofizika i Noveishie Tekhnologii. 31(2009) 1573-1587.


[2] A.A. Popov, S.V. Grib, O.A. Elkina, O.M. Ivasishin, P.E. Markovskii, I.A. Skiba, Effect of heat treatment and plastic deformation on the structure and elastic modulus of a biocompatible alloy based on zirconium and titanium, Physics of Metals and Metallography. 113 (2012) 382-390.


[3] S.V. Grib, O.M. Ivasishin, A.G. Illarionov, A.A. Popov, Effect of cold plastic deformation on the structure and physicomechanical properties of a biocompatible alloy of the Zr-Ti-Nb system, Physics of Metals and Metallography. (2019). In print.


[4] Xing Wang, Ligang Zhang, Ziyi Guo, Yun Jiang, Xiaoma Tao, Libin Liu, Study of low-modulus biomedical β Ti-Nb-Zr alloys based on single-crystal elastic constants modeling, Journal of the mechanical behavior of biomedical materials. 62 (2016) 310- 318.


[5] S.L. Demakov, A.G. Illarionov, M.A. Ivanova, Yu.N. Loginov, Forming texture at the manufacturing stage of copper wire, Cables and wires. 2 (2012) 8-13.


[6] P.P. Pal-Val, V.D. Natsik, L.N. Pal-Val, A.A. Davydenko, A.P. Rybalko, Yu.N. Loginov, S.L. Demakov, A.G. Illarionov, Unusual Young’s modulus behavior in ultrafine-grained and microcrystalline copper wires caused by texture changes during processing and annealing, Materials Science and Engineering A. 618 (2014) 9-15.


[7] M. Tane, S. Akita, T. Nakano, K. Hagihara, Y. Umakoshi, M. Niinomi, & H. Nakajima, Peculiar elastic behavior of Ti–Nb–Ta–Zr single crystals, Acta. Mater. 56 (2008) 2856-2863.